tag:blogger.com,1999:blog-5582579710677652457.post2836237906984196960..comments2024-03-23T13:23:47.586+05:00Comments on GNS3 Labs | CCNP | CCNA Labs: EIGRP single AS Configuration on GNS3 Waqas Azamhttp://www.blogger.com/profile/09328291791998119493noreply@blogger.comBlogger9125tag:blogger.com,1999:blog-5582579710677652457.post-23169742252702287872017-07-06T16:02:28.489+05:002017-07-06T16:02:28.489+05:00A loopback interface is a logical, virtual interfa...A loopback interface is a logical, virtual interface in a Cisco Router. A loopback interface is not a physical interface like Fast Ethernet interface or Gigabit Ethernet interface.<br />A loopback interface has many uses. <br />Loopback interface’s IP Address determines a router’s OSPF Router ID.A loopback interface is always up and allows Border Gateway Protocol (BGP) neighborship between two routers to stay up even if one of the outbound physical interface connected between the routers is down.<br />Loopback interfaces are used as the termination points for Remote Source-Route Bridging (RSRB), and Data-Link Switching Plus (DLSW+). Loopback interfaces interfaces are always up and running and always available, even if other physical interfaces in the router are down.Anonymousnoreply@blogger.comtag:blogger.com,1999:blog-5582579710677652457.post-49825606357973884172016-10-22T19:48:06.567+05:002016-10-22T19:48:06.567+05:00can iu tell me why you use lookback on router 1 an...can iu tell me why you use lookback on router 1 and router 6 i cant understand<br />Anonymoushttps://www.blogger.com/profile/03875725071877540855noreply@blogger.comtag:blogger.com,1999:blog-5582579710677652457.post-13998330976632041432014-05-07T20:06:15.011+05:002014-05-07T20:06:15.011+05:00plz write loopback eigrp configuration commands
plz write loopback eigrp configuration commands<br />Anonymoushttps://www.blogger.com/profile/02923823814214891716noreply@blogger.comtag:blogger.com,1999:blog-5582579710677652457.post-26603875104203055212013-11-25T10:27:25.350+05:002013-11-25T10:27:25.350+05:00Thanks for a simple walk-through, although the one...Thanks for a simple walk-through, although the one int g2/0 should be s1/0 on R6 but easy enough to find out by the illustration. Thanks for the helpAnonymousnoreply@blogger.comtag:blogger.com,1999:blog-5582579710677652457.post-75397121835634277782013-08-24T10:56:47.164+05:002013-08-24T10:56:47.164+05:00hi viki.it's very good and easy ti learn of ro...hi viki.it's very good and easy ti learn of route summarization.Anonymoushttps://www.blogger.com/profile/03298962339993416968noreply@blogger.comtag:blogger.com,1999:blog-5582579710677652457.post-18818603019070812102013-02-15T03:17:09.757+05:002013-02-15T03:17:09.757+05:00working fine thank you..working fine thank you..Anonymousnoreply@blogger.comtag:blogger.com,1999:blog-5582579710677652457.post-3399691243142232292012-07-04T22:14:24.840+05:002012-07-04T22:14:24.840+05:00Thank you for your quick answer viki. Could you by...Thank you for your quick answer viki. Could you by any chance post the .net files of your labs, that would be very helpful!Anonymoushttps://www.blogger.com/profile/15749675722658897702noreply@blogger.comtag:blogger.com,1999:blog-5582579710677652457.post-3213651437910762442012-06-20T17:12:19.166+05:002012-06-20T17:12:19.166+05:00hi serigne,
this gigabit interface that i manually...hi serigne,<br />this gigabit interface that i manually added in R6 you can use any other interface like FE, serial etc..Waqas Azamhttps://www.blogger.com/profile/09328291791998119493noreply@blogger.comtag:blogger.com,1999:blog-5582579710677652457.post-34359438109091705892012-06-19T17:48:07.957+05:002012-06-19T17:48:07.957+05:00How did you configured :
R6(config)#int g2/0
R6(co...How did you configured :<br />R6(config)#int g2/0<br />R6(config-if)#ip address 5.5.5.2 255.255.255.0<br />R6(config-if)#int g2/0 <br />What routers did you use and what images for this lab?<br />Thank youAnonymoushttps://www.blogger.com/profile/15749675722658897702noreply@blogger.com